How do I access my HP ProCurve console port?
To connect a console to the switch, use the console cable shipped with the switch and connect a PC or VT-100 terminal to the console serial port….
- Reconfigure the switch and save the new settings.
- Reconfigure the terminal and save the new settings.
- Reboot the switch and re-establish the console session.
How do I enable spanning tree on HP ProCurve?
The first thing to do is to select your root bridge (the central most switch in your network). Enter CLI and type “configure” to enter config mode. Then enter “spanning-tree” to enable it. That’s all you need to do on a switch to get STP up and running.
What does a ProCurve Switch do?
The HP ProCurve 1410-8G, 1410-16G, and 1410-24G Switches are multiport switches that can be used to build high-performance switched workgroup networks. These switches are store-and-forward devices that offer low latency for high-speed networking.
What is HP ProCurve Switch used for?
Yes, the HP ProCurve Switch 2224 is designed to be used primarily as a desktop switch to which end nodes, printers and other peripherals, and servers are directly connected, as shown in the illustration below. Notice that the end node devices are connected to the switch by “straight-through” twisted pair cables.
How do I manage my HP ProCurve switches?
How to: Configure a HP ProCurve switch
- Step 1: Connect your serial connection.
- Step 2: Conenct PuTTY.
- Step 3: Get the IP address.
- Step 4: Set time server.
- Step 5: Set SNMP community info.
- Step 6: Launch the web GUI.
- Step 7: Configure basic info.
- Step 8: Create VLANs.
How do I setup my HP ProCurve Switch?
Installing the switch
- Verify components shipped with the ProCurve 2520 Switch.
- Prepare the installation site.
- Verify that the switch passes self-test.
- Mount the switch and route the power cords.
- Connect power to the switch.
- Connect the network cables.
- (Optional) Install mini-GBICs.
Should spanning-tree be enabled on all ports?
You configure the command “spanning-tree portfast” on all the ports connecting to end devices like workstations. They then automatically bypass the wait period and DHCP works properly. It’s important to only configure this command on ports that connect to end devices though.
What is Admin Edge port?
Enabling immediate transition to forwarding on end nodes During spanning tree establishment, ports with admin-edge-port enabled transition immediately to the forwarding state. If a bridge or switch is detected on the segment, the port automatically operates as non-edge, not enabled.
What is the HP ProCurve switch 2626?
The HP ProCurve Switch 2626 is a low-cost, stackable, multi-layer, managed 26-port switch with 24 auto-sensing 10/100 ports and 2 dual-personality ports for 10/100/1000 or mini-GBIC connectivity. Manufacturer Website Address www.hp.com
How many 10/100 ports does the j4900b HP ProCurve 2626 have?
The J4900B HP ProCurve 2626 switch has 24 10/100 ports (IEEE 802.3 Type 10Base-T, IEEE 802.3u Type 100Base-TX); 1 RS-232C DB-9 console port; 2 dual-personality ports – each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type 10Base-T; IEEE 802.3u Type 100Base- TX;
What are the different types of ProCurve 2650 and 2626 backplane speeds?
13.6 Gbps (ProCurve 2650 and 2650-PWR)/9.6 Gbps (ProCurve 2626, 2626-PWR, 2600-8-PWR) backplane: wire-speed non-blocking architecture for low-latency throughput Basic IP routing: enables automatic routing to the connected VLANs and up to 16 static routes–including one default route–in IP networks
What is the power output of the HP switch 2650-pwr?
The HP Switch 2650-PWRand 2626-PWRare IEEE 802.3af compliant for Power over Ethernet and provide up to 15.4W per port. A redundant and external power supply is also available as an accessory. General Information Manufacturer Hewlett Packard