How do I fix my pace cable box?
How do I fix my pace cable box?
- Disconnect the power from your cable box by either unplugging the power cord from the wall outlet or from the back of the box.
- Wait 30 seconds.
- Reconnect the power cable to your cable box or outlet.
- Wait 3 – 5 minutes for the box to reset.
How do I reset my pace cable box?
To reset a Pace cable box, you need to power off the device and unplug it from the wall. Once you have done this, press and hold the “Menu” button on the remote control for 10 seconds. Plug in the device and wait for it to power back on. After that, your Pace cable box should be reset.
What do you do when your cable box wont turn on?
Restart your TV box
- Power off your TV Box.
- Remove the power cable from the back of the unit.
- Unplug the power cable from the wall outlet or power bar.
- Wait 30 seconds, then reconnect the power cable.
- Wait 30 seconds to 2 minutes for the TV box to reboot.
- Power on your TV box to see if it works.
How do you set up a pace cable box?
Pace Set Top Box Instructions
- Connect the coaxial cable wire coming from the wall, this cable carries the main cable TV signal, into the RF-in connector labeled “Cable In” on the back of the Pace set-top box.
- Plug one end of the red A/V cable into the red “R” “Audio Out” jack on the back of the Pace set-top box.
Why is my Spectrum cable box not working?
Most problems can be resolved by sending a refresh signal to your Spectrum Receiver. You an also try to reboot your receiver by unplugging the power cord and allowing at least 60 seconds before plugging it back in. Allow at least 20 minutes for the receiver to fully recover and then turn it back on.
Should I leave cable box on all the time?
Yes – power savings depend to a large degree on how much time the device is powered down. To maximize your savings, always power down your TV Box when you are done watching TV.
How can you tell if your cable box is bad?
Power off your TV Box. Remove the power cable from the back of the unit….What are the signs of a bad HDMI cable?
- “Shooting stars” or sparkling in the picture.
- Fuzzy or blurry picture.
- No picture or intermittent picture.
- No sound or intermittent sound.
- Weird colors in the picture.
- Remotes don’t work.
What to do if cable is not working?
Reboot the TV and the Cable Box To do this, either use your remote or the power button on the box itself. Then, wait for a few minutes to turn it back on. After that, reboot your TV. Turn off your TV and wait for a few minutes to turn it back on as well.
What is a pace DC550D?
Pace’s DC550D “Tango” High-Definition set-top box (STB) introduces the latest advanced video technology in a feature-rich and cost-effective MPEG-4 / MPEG-2 HD box. The DC550D’s embedded conditional access module enables operators to deploy a cost-effective, secure video decryption solution.
How much did you pay for the pace dc550d?
I bought a Pace DC550D on boxing day for $99.00 and a Sony Bravia KDL 40EX500 LCD TV. I came home activated the box and when everything was done plugged the receiver via HDMI into the TV.
How do I check the signal on the pace dc500d?
aviography: If you have the Pace set to pass all signals, then the TV should show the incoming signal by pressing the info/recall or similar button on the TV remote. 57, the Pace DC500D is an all digital HD box, no analogue tuner.
Does the dc550d have coaxial audio out?
The DC550D only has an optical (toslink) digital audio out, no coaxial SP/Diff connection. Anyone else run into this and how did you resolve it… Go after the retail store for an optical cable or Cogeco and see what they say?
Why won’t my Cogeco pace work with HDMI?
It really should not be this hard, it either works or it does not. Cogeco of course will always tell you they do not support HDMI. You do not need to unplug the HDMI cable,try just turning the Pace box off then back on. It usually comes down to an hdmi handshake issue.